Fibaro
Fibaro Wall Plug UK (FGWPG-111)
- Native integration
- Local control
- Z-Wave
Prices verified September 2026
See more smart plugs & energy picks on our Amazon storefront →Our verdict
The best Z-Wave smart plug with genuine UK BS1363 pins — accurate energy monitoring, S2 security and a colour LED ring that shows load at a glance. At £42-55 depending on retailer it costs more than the Zigbee energy plugs we cover elsewhere, and the premium only pays off if you're already on Z-Wave: every Wall Plug repeats the mesh, extending range to door locks and battery sensors further from the hub. It's also a chunky ~56mm cube that can overhang and block a neighbouring socket on a double gang outlet — check clearance first. S2 security is the right call here, since unlike a battery sensor this thing is mains-connected and always on.
What can Home Assistant control on the Fibaro Wall Plug UK (FGWPG-111)?
| Control | Type | What it does |
|---|---|---|
| Switch | Toggle | Turn the plug on/off |
| Power | Sensor (W) | Live power draw — updates in ~0.2W steps below 5W, so small loads refresh slowly |
| Energy | Sensor (kWh) | Cumulative energy used |
| LED ring colour | Configuration parameter | Set the load-indicator ring colour via Z-Wave JS config (not a separate entity) |
Zigbee JS reports power/energy on a threshold basis rather than continuously — under roughly 5W the plug only pushes an update every ~0.2W change, so a small load like an idle phone charger can sit un-refreshed in HA for a noticeable stretch. That's actually usable: treat "no power delta for N minutes while the switch is on" as a finished-charging-cycle signal, which only works because of this plug's specific low-load reporting granularity — coarser Wi-Fi plugs don't report finely enough for the same trick.
Specs
| zwave | Z-Wave Plus, S2 security, network repeater |
|---|---|
| extras | Colour LED load ring |
| max load | 13A resistive/general purpose, 8A incandescent, 750W motor, 3A electronic ballast |
| plug type | BS1363 (UK 3-pin, Type G) |
| dimensions | 56 x 56 x 58.5 mm (W x H x D) |
| power supply | 230V AC, 50/60Hz |
| energy monitoring | true |
| operating temperature | 0-40°C |
How does the Fibaro Wall Plug UK (FGWPG-111) compare?
| Product | From | Protocol | Local control | Integration |
|---|---|---|---|---|
| Fibaro Wall Plug UK (FGWPG-111) (this product) | £41.61 | Z-Wave | Yes | Native |
| Aqara Power Plug H2 UK (RGB) | £32.99 | Zigbee, Thread, Matter, Bluetooth | Yes | Works with HA |
| Aqara Wall Outlet H2 UK | £67.99 | Matter, Thread, Zigbee | Yes | Native |
| Eve Energy (Matter) UK Smart Plug | £39.95 | Thread, Matter, Bluetooth | Yes | Works with HA |
Frequently asked questions
- Does the Fibaro Wall Plug UK (FGWPG-111) work with Home Assistant locally?
- Yes. The Fibaro Wall Plug UK (FGWPG-111) is controlled locally in Home Assistant through a built-in Home Assistant core integration (zwave_js), so it keeps working if your internet connection or the Fibaro cloud goes down. Control and state updates stay on your own network.
- Which protocol does the Fibaro Wall Plug UK (FGWPG-111) use, and do I need a hub?
- The Fibaro Wall Plug UK (FGWPG-111) uses Z-Wave. To pair it with Home Assistant you need a Z-Wave controller stick attached to your Home Assistant host. Fibaro's own hub is not required when you integrate through a built-in Home Assistant core integration (zwave_js).
- How much does the Fibaro Wall Plug UK (FGWPG-111) cost in the UK?
- The lowest price we have listed for the Fibaro Wall Plug UK (FGWPG-111) is £41.61 at Amazon UK, with other UK retailers at up to £55. Prices were last checked in September 2026 and change often, so confirm on the retailer's page before buying.